XBee-PRO 868
------------

Customer Release Notes
----------------------

Copyright (C) 2015, Digi International

- - - - - - - - - - - - - - - - - - - -

### Overview:

These release notes document changes made to the firmware on the XBee-PRO 868.

### Links:

[Product Information](http://www.digi.com/products/wireless-wired-embedded-solutions/zigbee-rf-modules/point-multipoint-rfmodules/xbee-pro-868)  
[Documentation](http://www.digi.com/products/wireless-wired-embedded-solutions/zigbee-rf-modules/point-multipoint-rfmodules/xbee-pro-868#docs)  
[Support](http://www.digi.com/support/productdetail?pid=3553)

### Compatible Hardware:

* XBee-PRO S5
	* XBP08-DP

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1061 - XBee-PRO 868
* 1161 - XBee-PRO 868, RS232 Adapter
* 1361 - XBee-PRO 868, RS485 Adapter
* 1461 - XBee-PRO 868, USB Adapter
* 1661 - XBee-PRO 868, Analog I/O Adapter
* 1761 - XBee-PRO 868, Digital I/O Adapter

### Release Date: 

* 2011-Jan-06

### New Features:

* Added asynchronous sleep modes and support for indirect messaging.

### Bug Fixes:

* Increased the time that a node will wait to receive a network discovery response to account for 
  the time it takes for the request to propagate.

* Fixed bug where no status was returned for a failed RMT AT CMD Request transmission.

* Fixed a bug where the PWM-RSSI output was not correct.

* Fixed a problem where DIN/DOUT were not configured correctly for AIO/DIO adapters.

* Changes to the ATCT (command mode timeout) would not be applied until after command mode was 
  exited (even if an ATAC was done). This has been fixed.

* Fixed bug where an incomplete API frame would corrupt the next API packet in API mode 2.

* Fixed bug where the pullup on DIN was not getting properly set.

### Known Issues / Errata:

* None

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1027 - XBee-PRO 868
* 1127 - XBee-PRO 868, RS232 Adapter
* 1327 - XBee-PRO 868, RS485 Adapter
* 1427 - XBee-PRO 868, USB Adapter
* 1627 - XBee-PRO 868, Analog I/O Adapter
* 1727 - XBee-PRO 868, Digital I/O Adapter

### Release Date: 

* 2009-May-21

### New Features:

* None

### Bug Fixes:

* Updated the .mxi file with ATIC, ATIR, ATLT, ATSB, ATD9, ATCK commands.

* NI strings maintain case now.

* ATM0, ATM1 are set when command mode exits or AC. ATM0, ATM1 can also be read.

* Code changes made to improve manufacturing yields.

### Known Issues / Errata:

* If the receiving module is streaming data out the UART and a ‘+++’ is sent to the module it will 
  not enter command mode until after there is a break in the data.

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1026 - XBee-PRO 868

### Release Date: 

* 2009-Feb-13

### New Features:

* None

### Bug Fixes:

* Fixed a problem where DIN/DOUT were not configured correctly for AIO/DIO adapters.

### Known Issues / Errata:

* If the receiving module is streaming data out the UART and a ‘+++’ is sent to the module it will 
  not enter command mode until after there is a break in the data.

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1030 - XBee-PRO 868

### Release Date: 

* 20xx-Xxx-xx

### New Features:

* Note: This is a special interim release.

### Bug Fixes:

* Fixed PWM RSSI Default - ATRP to 0x28.

### Known Issues / Errata:

* If the receiving module is streaming data out the UART and a ‘+++’ is sent to the module it will 
  not enter command mode until after there is a break in the data.

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1025 - XBee-PRO 868

### Release Date: 

* 2009-Jan-12

### New Features:

* ATIS, ATIC and ATIR commands added for AIO and DIO support.

* ATLT command added to set the power LED blink rate.

* ATCK diagnostic command was added to hash the current user configuration.

### Bug Fixes:

* Fixed a problem with unshipped production units where PL=2 was outputting too much power.

* Fixed a problem where ack's failed because the ack duty cycle was incorrectly limited to 1% 
  rather then 10%.

### Known Issues / Errata:

* If the receiving module is streaming data out the UART and a ‘+++’ is sent to the module it will 
  not enter command mode until after there is a break in the data.

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1023 - XBee-PRO 868

### Release Date: 

* 2008-Nov-07

### New Features:

* None

### Bug Fixes:

* Fixed problem with loopback, where the endpoints were not getting swapped.

### Known Issues / Errata:

* None

- - - - - - - - - - - - - - - - - - - -

### Release Version:

* 1022 - XBee-PRO 868

### Release Date: 

* 2008-Oct-15

### New Features:

* Initial release.

### Bug Fixes:

* None

### Known Issues / Errata:

* None