Release Notes PN 93000342 Digi AccelePort Xp, RAS and Sync Drivers Version 4.0.229.0 Microsoft Windows NT 4.0 Service Pack 5 or higher Software Package PN 40001974_L 05/21/2002 INTRODUCTION This driver supports all Digi adapters listed below. These adapters provide connectivity in a Windows NT 4.0 environment and support a broad range of WAN connections, including serial, V.90 modems, ISDN (BRI and PRI), Frame Relay, SNA (SDLC, X.25/QLLC), PPP and X.25 protocols. Digi International announced the discontinuation of the DataFire RAS product line in September 2001. In our continued effort to support DataFire RAS customers, we entered into a definitive agreement to sell the DataFire RAS product line to Patton Electronics Company in November 2001. All business areas related to the DataFire RAS product line are now handled by Patton Electronics. If you have any technical questions with respect to the DataFire RAS product line, please contact Patton Electronics via e-mail at support@patton.com, or call 1-301-975-1000 and ask for the technical support team. Additional information is also available on the Patton Electronics website at , including driver updates and future releases. Please note that the AccelePort RAS product line is NOT part of the DataFire RAS product line acquisition by Patton Electronics. Digi International will continue to sell and fully support all AccelePort RAS products without restrictions. SUPPORTED PRODUCTS AccelePort Xp Family of Adapters: AccelePort 2p AccelePort 4p AccelePort 8p AccelePort 16p DataFire RAS PTE Family of Adapters: DataFire RAS 24 PT1 DataFire RAS 48 PT2 DataFire RAS 30 PE1 DataFire RAS 60 PE2 DataFire RAS B4STU Family of Adapters: DataFire RAS B4U DataFire RAS B4ST DataFire DSP CompactPCI Family of Adapters: DataFire DSP 24 PT1 CompactPCI DataFire DSP 48 PT2 CompactPCI DataFire DSP 30 PE1 CompactPCI DataFire DSP 60 PE2 CompactPCI AccelePort RAS Family of Adapters: AccelePort RAS 4 AccelePort RAS 8 DataFire SYNC 2000 Family of Adapters: DataFire SYNC 2000 2P PCI DataFire SYNC 2000 2P+ PCI DataFire SYNC 2000 4P PCI DataFire SYNC 2000 4P+ PCI DataFire SYNC 2000 2P CompactPCI DataFire SYNC 2000 2P+ CompactPCI DataFire SYNC 2000 4P CompactPCI DataFire SYNC 2000 4P+ CompactPCI DataFire SYNC/570 Family of Adapters: DataFire SYNC/570-ISA 2P EIA232 DataFire SYNC/570i-ISA 2P EIA232 DataFire SYNC/570i-ISA 2P X.21 DataFire SYNC/570i-ISA 2P V.35 DataFire SYNC/570i-ISA 4P EIA232 DataFire SYNC/570i-ISA 4P V.35 DataFire SYNC/570i-PCI 2P UIB DataFire SYNC/570i-PCI 4P UIB DataFire SYNC/570i-56-ISA EIA232 RJ45 DataFire SYNC/570i-56-ISA V.35 RJ45 KNOWN LIMITATIONS Installation/User Interface: Within the wizard mode, if invalid input has been entered and back button is pressed, an error message might appear indicating that the input is invalid. Valid input needs to be entered to be able to go back. PortAssist Viewer: The PortAssist Viewer shows a Line Speed and Configured Baud Rate of zero for the SYNC/570 if the link is externally clocked. If the link is internally clocked both values show the Configured Baud Rate. The SYNC/570 does not calculate the Line Speed. PortAssist Viewer shows a protocol of SDLC for QLLC SNA links. Use the raw data for problem diagnosis. RAS Adapters: On Channelized T1 Wink Start Trunks without dial tone super- vision, modems must be initialized with ATX3 for dial out. When configuring dial-up modem service for a line, all modems on the line should be configured since incoming calls may be assigned to any channel. On ISDN Trunks, the following rules are applied to modem dial strings: 1. A comma (delay) in the first or second position is allowed. 2. Then the first non-numeric character terminates the dial string (e.g. 9,12345678 is a valid dial string and 9,1,234-5678 is not). SYNC Adapters: For PPP links, both sides of a connection must disconnect before they can be reconnected. When using the SDLC interface, the maximum BTU (Basic Transmission Unit) is limited to 521 bytes. This is a known limitation of the IBM SDLC link service provided in SNA Server. See the Microsoft SNA article, "Maximum BTU Limit for Dumb SDLC Interface" for more information. HISTORY Version 4.0.229.0 (L Release) BUG FIXES Fixed: DataFire Sync configuration dialog for X.25 does not show up. (#8068) Fixed: WanLinks driver doesn't remove keys from SERIALCOMM when uninstalled (#8412) Fixed: The DigiAsyn.sys driver is hanging in an endless loop (#7656) Fixed: Parity error detection failure with AccelePort Xp (#7542) Fixed: Microsoft FAX does not work with AccelePort Xp (#5702) Fixed: Unable to print with AccelePort Xp (#5081) Fixed: Multiple issues with E1/R2 parameter configuration (#7956, #7897) Fixed: The DigiAsyn.sys driver doesn't handle zero length read requests correctly. Fixed: Some timed-out writes are being inadvertently completed with STATUS_CANCELLED Fixed: Write timeout does not work when Write Complete When Sent option is enabled Fixed: If low latency is enabled, any attempt to open the port causes the system to completely lock up Updated DataFire RAS firmware to M release. Detailed information about firmware enhancements and bugfixes can be found in the DataFire RAS firmware Release Notes. Version 4.0.217.0 (L3P) BUG FIXES Fixed: Caller DID option within Windows 2000 server is not working (#5576) Note: Fixed for AccelePort Xp only. Fixed for Windows NT 4.0 too. Fixed: E1/R2 GroupB and backward signalling range incorrect (#5653) Fixed: Add Channel Mapping option for DataFire RAS24/48/30/60 CT1 and PRI (#7380) Fixed: Driver does not start when installing L2P from scratch (#7582) Fixed: Ntperf reports same throughput on AccelePort Xp port at these baud rates - 1200 2400 4800 9600 19200 (7570) Fixed: AccelePort Xp fails the sndrcv test application (#7354) Fixed: Throughput problems with AccelePort Xp at 921kbps on Windows NT 4.0 (#5173) Version 4.0.214.0 (L2P) BUG FIXES Fixed problem establishing a fax connection (#7220,#5702) Fixed serial printing errors (#7493) RasAudio.exe was missing from the build (#7234) Fixed DigiInf.dll load issue (#7231) Changed Sync2000 PLX9080 setup to initialize in PCI 2.1 mode. Problem with modem country setting for E1/T1 cards (#5073 & #6376) Port Assist Viewer doesn't display RAS30/60 boards in E1R2 mode (#5071) Port Assist Viewer doesn't show ISDN layer 3 status (#3976) Port Assist Viewer faults when clearing statistics (#2495) Version 4.0.210.0 (L1P) This version was not released to the public.